Third Eye Gypsy(Genea Beads) 2011 by Parigo Studios 2010

Thursday, June 28, 2012

HOT, HOT, HOT- Kalypso Silver glass Discoveries & Tutorial

Hello friends!

Well it is HOT outside for sure! I guess that makes this a perfect time to post for a few reasons. 1. It's too hot to turn on a kiln and torch inside when it's about 104 outside. 2. These firey got glass colors are prefect for the hotness outside.

So you may have been seeing my beads pop up on my facebook as I have been making them. I was fortunate to have a ton of luck with the silver glass considering I don't really use it much in my work. The glass will run you about $100lb which is CRAZY expensive for glass. The glass is so pricey due to it's high silver content.

I ventured out on my silver glass discovery to match my  Copper Big Hole focal for Kristi's Challenge.
Here was the donut I received from Kristi. I didn't quite capture all of the gorgeous pinks and oranges in my donuts heat patina, but trust me, they are there.
Here is where my adventure began. I checked out a few quick notes from Double Helix to see how to work the glass. I had all of ONE rod to not only learn, but to create some special beads! Yikes! How's that for pressure?! Here is what I learned...

From left to right:
B1- effetre White, Rubino, super clear, Kalypso and super clear. 
B2- effetre Clear, effetre Orange, Kalypso.
B3- Messy Peace, Messy Cranberry, Messy Clear, Kalypso, and Messy Clear.

*B4- Peace base, Cranberry, Messy Clear, Kalypso, Messy Clear- I got these gorgeous results by layering all of the glasses to Kalpyso. 

You super heat kalypso as you melt it into the surface. The glass will somewhat look clear. You want it kind of hot and soupy.  Then you let the bead cool til the glow completely dies out. Check your bead under you work table where it's dark. I then turned down my oxygen to make a reduction flame. I flashed the bead in and out of the flame until the silvery luster appeared. Keeping your bead out of the flame, turn back to a neutral flame, and encase in clear, taking special care NOT to get your bead directly into the flame as you will burn off the luster you just added. When you have encased the bead, bring it to the back of the flame and gently heat. You will see an iridescent blue flash as you are melting in the glass. DON'T OVER HEAT! If you don't see those blue flashes in the glass you have melted off the luster even under the clear encasement.

Also *** Make sure to get your Rubino, Cranberry, and Clockwork covered in clear! If they touch Kalypso you will see black as the silver glass and other glasses have a chemical reaction.

B5-Peace base, Cranberry, Messy Clear, Kalypso, Messy Clear. 

*B6- Messy Clear, Clock Work, Messy Clear, Kalypso and Messy Clear.

I did the steps above and reduced again(turn down oxy flame til you get a bushy flame). You will see the blues appear as you reduce. Gently flash in and out of the flame until you get a nice sheen on your bead. Encase like above.

B7- effetre Sunny Mango Coral odd lot, effetre Transparent Orange, Messy Clear.
B8- effetre Sunny Mango Coral odd lot, Messy Clockwork, Messy Clear, Kalypso, Messy Clear.
*B9- effetre Opal Yellow, effetre Rubino, Messy Clear, Kalypso, Messy Clear.

Followed the same steps as above for * results. It seems like you could see the luster in the bead when you after it was worked and put into the kiln. So if it looks pretty going in, it will be gorgeous coming out of the kiln later! It's nice that you can see the results and know you got the glass to sing :)

Below you can see the AMAZING results I got from the * posts above. I think the Clockwork, Messy Clear, Kalypso, and Messy Clear produced the best results! Those are the first 6 results from left to right. 

For more of a golden orange results like the next to spiral coin beads, I used: Peace, Cranberry, Messy Clear, Kalypso, and Messy Clear. 

FOR BEST RESULTS:

To get the ULTRA blue/purple iridescence you want to reduce the bead until the sheen looks dark. It doesn't take long. It also looks like you may have over-reduced the bead, but as you encase the bead and re-heat it in the flame to melt down the encasement you will see it lighten and the blue iridescent flashes appear!

The bright pink flahes come from super heating the Kalypso when you first melt in the layer of glass. make sure to use a hot oxidizing flame to get the glass clear looking when you melt on the Kalypso layer!

I have found that using Clock work under Kalypso gives you the perfect mix of firey orange to go with the hot pink and blue/lavender iridescence. 

Want to see what you can create using those techniques???
Just look at all of that COLOR!

Look at those gorgeous flashes of iridescence on the firey HOT pink and orange!

Be sure to stop back to see how I incorporated this incredible beads into my desgin with Kristi's gorgeous Copper large hole focal!

See ya on Saturday!!

xo Genea

6 comments:

KristiBowmanDesign said...

Oh my are you putting some of those gorgeous glass beads with my copper, that's going to look soooo yummy!! I love that last flower, amazing! Thanks!

Alice said...

Wow, the colors in those beads are gorgeous! I can't wait to see how you use them with Kristi's copper big hole pendant.

Unknown said...

So since I am totally not allowed to play with fire I will tell you that I will leave it all to you! Gorgeousness!!!!!!!

Third Eye Gypsy said...

Kristi- Yep!! It's f*ing amazing, actually ;D

Thanks so much!

Alice- Thanks so much! I can't believe the intensity of the colors I got with the glass! Yay! I can't wait to share!

Kristen- Awww! Yep, I'll do it for ya! Thanks so much!

xo Genea

Libellula Jewelry™ said...

I'm definitely looking forward to seeing what you make with those gorgeous beads!

Third Eye Gypsy said...

Libellula- I can't wait to share! See you all Saturday!

Post a Comment

Thank you for your comment. I love it when you share your thoughts with me :)